Sometime ago my Vita started showing up the "GPU error message" (when on 3.65 and 3.68) and the "Ps Vita System will be Powered Off" (when on 3.60), thanks do The Flow's Modoru we now, as long as hackable, can switch between firmwares, to test, to choose, and I, that was on 3.65 enso, and from time to time having this problem, started to search for a solution online...
So, first I saw people saying that I should put my plugins, all on ux0 instead of ur0, did it, changed the config.txt, then swapped all to ur0 when it still happens, started to change firmware to test it and actually was getting worst, tried rebuild database, wipe memory card, nothing, now even graphical glitches was happening, so I took a deep breath and started to think on my on, and here's the solution I have found:
A) Use Modoru to go to firmware 3.60
B) Rebuild Database from Safe Mode
C) Format Memory Card from Safe Mode
D) Restore System from Safe Mode and don't pass the opening "Welcome & Configuration" when it restarts after System Restoration turn it off! Don't put anything yet!
E) Reinstall current Firmware (3.60) from Safe Mode, using PC option, QCMA seted up with the 3.60ofw .PUP at Update folder on your PC, and using the option of latest firmware as 3.60 (Henkaku), also turn off the option "Automatic Database Refresh (Experimental)" on QCMAs Settings.
F) After reinstalling the Firmware (3.60) using the QCMA via Safe Mode's PC Option to Update Firmware, you can now do the opening "Welcome & Configuration" when rebooted, select that you have a PSN account but will set it up later
G) Connect to your Network, go to the browser and type in: ' henkaku.xyz/go ' , the henkaku installer via browser, so you can spoof the PSN to login on your account and start using QCMA Content Manager (and FinalHE, by soarqin).
H) After installing Henkaku, make sure to have, on Henkaku Configurations Spoof Version seted to 3.70, inside Configurations, Log In on your PSN account. Reboot. (AFTER LOGIN AND REBOOT DON'T OPEN HENKAKU AGAIN OR THE NEXT STEP WILL FAIL)
I) After reboot, using FinalHE, by soarqin, on PC, you can now easily transfer H-Encore to you Vitas Memory Card via Content Manager (don't need QCMA here / Make sure ir says you are on 3.60 fw at FinalHE app on PC). Open H-Encore after installing it (following the stepts of the app on your PC), select "reset config.txt", install henkaku, then download Vitashell. Enable Unsafe Homebrew via Henkaku Config
J) Transfer the Enso 3.60 Installer (from official ' enso.henkaku.xyz ' ) to your PSVita via Vitashell [ ! We are not going to install the Enso itself, only the app ! ] .
K ) After installing THE APK, open Enso (APK) application on your Vita, press O (Circle) and then ٨ (Triangle) !!!!! , the option to Uninstall the Enso, your Vita will reboot then. This will clean up some files and folders that may be dirty.
L) Uninstall H-Encore and the Enso app, they both only works for 3.60 on this versions and we're going to update to 3.65 now.
M) Boot on Safe Mode and install 3.65 ofw via QCMA on your PC (set up Latest Firmware as Custom 3.650.000).
N) After updating, install again H-Encore via FinalHE, open H-encore holding R select "Reset Config.txt" and install Henkaku. Select Enable Unsafe Homebrew at Henkaku Config.
O) Download, transfer and install Enso Installer for 3.65 by TheFlow and again just the apk, open it, circle, triangle, uninstall it, will reboot.
P) Now, open H-Encore and we are good to go.
Just a few important things:
When installing plug ins, such as NoNpDRM, install on both ux0:tai and ur0:tai directories, having the .skprx (or .suprx) on both folders, inside each 'config.txt' of each separate folder, then put the directions to their respective directories, example: when installing NoNpDRM put it on both ux0 and ur0 tai folder the skprx and on config.txt of ux0:tai, should be ux0:tai/nonpdrm.skprx under *Kernel and on config.txt at ur0:tai, ur0:tai/nonpdrm.skprx. They all should be at the same order on both, so the system will use each config as the same, loading plugins inside their on directories, cuz sometimes the memory card doesn't load constantly, so it will not have a fail reading.
Remember to have every .skprx on config.txt list inside each folder, even the henkaku one, then change his directory where listed on the config.txt . ( Observation: The > Keys.bin < from ref00d, that one should only be at ur0:tai )
Also use TaiHen.skprx, by yifanlu, at top *Kernel on both configs and folders, using the same method explained.
Always use the option to Refresh Licenses at ٨ (triangle) on VitaShells options when installed a new application.
p.s.: reF00D.skprx always after nonpdrm.skprx
p.s.: Use always a charger that is a output 5V - 1.2A for the sake of the internal components.
––> Feel free to spread the word.
Advertising